This page presents download files and installation instructions to update your Multisensor six via OTA software and form part of the larger Multisensor 6 user guide.

Update Multisensor 6 firmware via HomeSeer.

Our guide to upgrading Multisensor 6 firmware via HomeSeer can be found past post-obit the given link.

Update Multisensor 6 firmware via Z-Stick or Z-Stick Gen5.

As a part of our Gen5 range of products, MultiSensor half-dozen is firmware upgradable. Some gateways will back up firmware upgrades over-the-air (OTA) and take MultiSensor 6'south firmware upgrades packaged equally office of their platform. For those that don't still support such upgrades, MultiSensor 6'due south firmware tin exist upgraded using Z-Stick from Aeotec (or whatever other Z-Wave compliant Z-Wave USB Adapters from whatsoever manufacturer) and Microsoft Windows.

Warning -

  • Exercise not update V1.08 to V1.09 or later, this volition brick older MultiSensor vi units.

Requirements:

  • Windows PC (XP and in a higher place)
  • Z-Wave USB Adapter (Z-Stick, UZB1, SmartStick+, or other standard Z-Moving ridge USB Adapters can exist used)

Firmware Changelogs:

- Change logs of all firmware versions.

V1.15 Changelogs:

  • Fixes Calorie-free Sensor reporting aberrant values on occasion

V1.14 Changelogs:

  • Basic Ready faster report trigger when motion detected (when Parameter 5 [1 byte] = one)
  • Support new hardware light sensor Si1133
    • Backwards compatible to older light sensor Si1132 (used in firmware V1.13 and under)

To upgrade your MultiSensor 6 using a Z-Stick or whatever other general Z-Wave USB Adapter:

  1. If your MultiSensor vi is already part of a Z-Wave network, please remove it from that network. Your MultiSensor 6 manual touches on this and your Z-Wave gateway's / hub's user manual volition provide more specific information. (skip to step 3 if it is part of a Z-Stick already)
  2. Plug the Z‐Stick controller to the USB port of your PC host.
  3. Download the firmware that corresponds to the version of your MultiSensor 6.

    Warning    : downloading and activating the wrong firmware will brick your MultiSensor and return information technology cleaved. Bricking is not covered by warranty.

    V1.fifteen
    Australia / New Zealand frequency - version 1.15

    Eu version frequency - version 1.fifteen

    U.s.a. version frequency - version 1.15

    Russian version frequency - version 1.15

         V1.ten
    Japanese version frequency - version ane.x

  4. Unzip the firmware ZIP file and change the name of " MultiSensor_6_*** .ex_" to " MultiSensor_6_*** .exe ".
  5. Open up the EXE file to load the user interface.
  6. Click CATEGORIES and then select SETTINGS.

     7.  A new window will popular up. Click the DETECT button if the USB port is not automatically listed.

      8.  Select the ControllerStatic COM port or UZB, and so click OK.

      nine.  Click Add NODE. Let the controller into inclusion mode. Short printing the MultiSensor 6'southward "Activeness Button". At this stage, the MultiSensor 6 will be added to the Z-Stick's own Z-Wave network.

     x. Highlight the Multisensor 6 (shows every bit "Sensor Multilevel" or select it based off the Node ID).

     xi. Select FIRMWARE UPDATE and then click START. The over-the-air firmware upgrade of your MultiSensor 6 will brainstorm.

     12. If the Multisensor 6 is battery powered, the firmware update may non initiate correct away. just tap the button on the Multisensor six then the update should begin.

     xiii. After about v to x minutes, the firmware upgrade will exist completed. A window will pop up with the status "Successfully" to confirm successful completion.

     14. If you observe whatever issues from your device not existence able to set configurations properly, delight make certain to showtime unpair your Multisensor from your network to avoid phantom nodes, then run a factory reset by holding the Multisensor 6 action push for 20 seconds.

     15. Now re-include your Multisensor half dozen dorsum into your network.